信賴性保證與失效分析

在生產流程中進行全面性的品質保證工作，切實執行每一個檢測過程中的環節與步驟，盡全力達到100%的客戶滿意度。泰藝所屬工廠均導入+/-3σ策略來強化產品品質，各項先進且完備的測試儀器，規劃嚴格的檢驗標準及精準的作業規範下，確保產品功能完整、使用穩定，對品質的堅持，贏得客戶高度信賴與肯定！

測試項目		測試條件			所參照的國際標準		儀器圖片
高壓試驗	Leak rate less than 2*10-8 atm.cc/sec				MIL-STD-883 1014
空氣漏比率試驗	Leak rate less than 2*10-4 atm.cc/sec				MIL-STD-883 1014
冷熱衝擊試驗	-55℃, 125℃; soak time is 10 mins, with total 200 cycles				MIL-STD-883 1010 Condition B
耐濕偏壓試驗	85℃/85% RH for 500 hrs				JESD22-A101
耐冷測試	-40℃ for 500 hrs				IEC 60068-2-1
工作壽命試驗	25℃, 85℃, 125℃, test in period of 1, 2, 4, 7, 10, 20, 50, 100 days				MIL-STD-883 1005 Condition A or B MIL-STD-883 1008 Condition B
耐熱試驗(Metal Can)	260 ± 5℃ for 10 ± 1 sec				MIL-STD-202 210 Condition B
回流焊試驗(SMD)	Pre-heating: 150℃ to 200℃, 60~120secs. Heating: 217℃ , 60~150secs. Peak: 260±5℃ , 25±5secs. Go through twice.				J-STD-020D
焊錫性試驗	First procedure: Steam Aging 93℃ +3/-5, 8 ± 0.5hrs. And then: Dipping 245±5℃ , 5 ± 0.5sec.				JESD22-B102
機械衝擊試驗	1500g, half-sine, duration: 0.5ms , each axis for 3 times				MIL-STD-883 2002 Condition B
振動試驗	10~2000Hz, 1.52mm, 20g, each axis for 4 hrs				MIL-STD-883 2007 Condition A
鹽霧試驗	35 ± 2℃, 5% salt spray for 96 hrs				MIL-STD-883H 1009.8 condition C IEC 60068-2-11
彈跳試驗	40g / 6ms ,each axis for 4000 times.				IEC 60068-2-29
降落試驗	70, 80, 90cm, each height for 3 times on hardboard				IEC 60068-2-32
扭力試驗	Deflection: 3mm for 30 sec				IEC 60068-2-21
推力試驗	10N for 10 sec				IEC 60068-2-21
壓力試驗	10N for 10 sec				IEC 60068-2-21
拉力試驗	10N for 10 sec				IEC 60068-2-21